At Area 419 we decided that there were no scope bases on the market that really met our requirements for quality, so we made our own. Its all in the little details that set this base apart from the competition. These are machined in house on our 4-axis HAAS VMC from 7075 Aluminum. Straight off the mill there is not a single sharp edge left, all corners are radiused and any necessary harsh corners are chamfered. Just like all of the other Picatinny products we make, we radius between the slots, and also radius the corners of the lugs to prevent any snag areas and give it a cleaner look.
- The MOA angle of the base is guaranteed to be true to the spec due to advanced fixturing
- Machined to MIL-STD-1913
- Type III Hardcoat Black anodized
- Comes with the necessary wrench for torquing the clamp screws
SA refers to Short Action, LA refers to Long Action, RH refers to Right Handed Actions, LH refers to Left Handed Actions
Notes:
- Tikka T3, SA – Fits Tikka T3 and T3x. All screws are T10 Torx and the same length. Comes with stainless recoil pin to work with receivers that have the hole available, rail will still work on those that do not
- Tikka T1x – All screws are T10 Torx and the same length
- Remington 700 LA – Integral machined in recoil lug bears against the front receiver ring to prevent any base shifting under recoil. Compatible with #6 and #8 screws, no modification necessary, both screw types included. Ejection port cut blends seamlessly into action and gives plenty of room for top loading ADL style rifles. All screws are the same length and sized to not interfere with barrel threads, no more guessing which screw goes where. #6 Screws = 15in/lb, #8 Screws = 20in/lb
- Remington 700 SA – Integral machined in recoil lug bears against the front receiver ring to prevent any base shifting under recoil. Compatible with #6 and #8 screws, no modification necessary, both screw types included. Ejection port cut blends seamlessly into action and gives plenty of room for top loading ADL style rifles. All screws are the same length and sized to not interfere with barrel threads, no more guessing which screw goes where: #6 Screws = 15in/lb. #8 Screws = 20in/lb
- CZ455 – For added security we have added a recoil lug at the rear of the base, creating a mechanical stop for the base. Recommended torque spec: 22 in/lb (2.5 NM). This base is a little taller than the popular set-screw models (our rail adds a total of about 1/2″ of height to the dovetail) but by using lower height rings/mounts you should be able to retain a similar over bore height and maintain a good cheek weld without any riser. These rails can also be used with the CZ 452, excluding the “American” model, which has a differently-sized dovetail. We also decided to build in a bubble level to the base. The material is flared out in the area to provide optimum viewing when in the prone position without much movement if any.
- CZ457 – We added real estate to the front of the rail to allow you to move your optic forward. This helps on higher powered scopes when coupled with the smaller stocks that are normal on a rimfire. This base is a little taller than the popular set-screw models (our rail adds a total of about 1/2″ of height to the dovetail) but by using lower height rings/mounts you should be able to retain a similar over bore height and maintain a good cheek weld without any riser. We also decided to build in a bubble level to the base. The material is flared out in the area to provide optimum viewing when in the prone position without much movement if any.
- Sako Quad – For added security we have added a recoil lug at the rear of the base, creating a mechanical stop for the base. Recommended torque spec: 22 in/lb (2.5 NM). This base is a little taller than the popular set-screw models (our rail adds a total of about 1/2″ of height to the dovetail) but by using lower height rings/mounts you should be able to retain a similar over bore height and maintain a good cheek weld without any riser. We also decided to build in a bubble level to the base. The material is flared out in the area to provide optimum viewing when in the prone position without much movement if any.
- Anschutz 1761 – Recommended torque spec: 22 in/lb (2.5 NM). We added real estate to the front of the rail to allow you to move your optic forward. This helps on higher powered scopes when coupled with the smaller stocks that are normal on a rimfire. This base is a little taller than the popular set-screw models (our rail adds a total of about 1/2″ of height to the dovetail) but by using lower height rings/mounts you should be able to retain a similar over bore height and maintain a good cheek weld without any riser. We also decided to build in a bubble level to the base. The material is flared out in the area to provide optimum viewing when in the prone position without much movement if any.
- Ruger 10/22 – Recommended torque spec: 15 in/lb. We added real estate to the front of the rail to allow you to move your optic forward. This helps on higher powered scopes when coupled with the smaller stocks that are normal on a rimfire.
- Ruger American, SA – Recommended torque spec: 15 in/lb
- Henry Lever Action – See below for FIT GUIDE
FOUR-SCREW (Long Action) fits the following Henry models:
H009, H009G, H009B, H009AW, H009GAW, H009CC, H009GCC, H009X, H009WL, H009GWL, H009BWL
H010, H010G, H010B, H010AW, H010GAW, H010CC, H010GCC, H010X, H010WL, H010GWL, H010BWL
H018-410 (with drilled and tapped receivers), H018-410R, H018AH-410
H024-3030, H024-35, H024-3855, H024-4570
Please note that this base will only fit H018-410 models with drilled and tapped receivers.
THREE-SCREW (Short Action) fits the following Henry models:
H006 (must be 2nd Gen with drilled/tapped receiver) and H012 Series hole spacing only.
Will fit the following Henry models:
H006, H006R, H006M, H006MR, H006C, H006CR, H006S, H006MS, H006CS, H006ML, H006MML, H006CML, H006D, H006D2, H006D3, H006D4, H006ES, H006TT, H006OM, H006GBA
H012, H012G, H012R, H012GR, H012AW, H012GAW, H012CC, H012RCC, H012GRCC, H012GCC, H012M, H012GM, H012MAW, H012GMAW, H012MRCC, H012GMRCC, H012MCC, H012GMCC, H012C, H012GC, H012CRCC, H012GCRCC, H012CAW, H012GCAW, H012CCC, H012GCCC, H012X, H012MX, H012CX - Savage SA – Recommended torque spec: 15 in/lb. This rail fits: Savage New 110 Short Action, 10, 11, 12, 14, 16 (6-48 screws)
Savage New 110 Short Action (8-40 screws) - Browning X-Bolt – Recommended torque spec: 15 in/lb. Our rails are available for short or long action receivers in 20 MOA
**Please note: Some photos may show a different MOA than what’s listed. Refer to the MOA in the dropdown menu for accuracy.
Available for the following:
- Tikka T1x, 15 MOA
- Tikka T1x, 30 MOA
- Tikka T3/T3x, SA, 20 MOA
- Remington 700, LA, 20 MOA
- Remington 700, SA, 20 MOA
- CZ455, 15 MOA
- CZ455, 20 MOA
- CZ457, 15 MOA
- CZ457, 30 MOA
- CZ457, 50 MOA
- Sako Quad, 30 MOA
- Anschutz 1761, 15 MOA
- Anschutz 1761, 30 MOA
- Ruger 10/22, 15 MOA
- Ruger 10/22, 30 MOA
- Ruger American, SA, 20 MOA
- Henry Lever Action, 3-Screw
- Henry Lever Action, 4-Screw
- Savage, SA, 20 MOA
- Browning X-Bolt, SA, 20 MOA
- Browning X-Bolt, LA, 20 MOA
ATP is an authorised Australian dealer for Area 419. All Area 419 products bought from ATP are covered by the Australian Area 419 Warranty.
